NXA-RGB is a plug-in RGB interface card for Modero VG series touch panels. Field upgradable, the card integrates with RJ-45 RGB connector found on all VG series panels.

• Improved speed and efficiency for USB mouse and keyboards (this feature requires NXA-AVB/RGB Modero RGB AV Breakout Box v1.12 or higher version).
• Improved HD satellite receivers synchronization

Changes in this release

Changed the Factory Defaults button semantics as follows:

Reset Configuration Data to factory defaults:

Press and Hold the 'Factory Defaults' button for about 5 seconds to request a change of the Configuration data back to factory defaults. The 'POWER' LED will blink 3 times to indicate that the system will now reset the configuration when the button is released. This will not affect the Firmware version. If you do not release the button after the '3 blinks' the system will proceed to keep counting towards the Firmware version factory default stage.

Reset Firmware Version to factory default:

Press and Hold the 'Factory Defaults' button for about 10 seconds to request a change to the Firmware version back to the factory default. The 'POWER' LED will blink 3 times when it gets to the 'Configuration' stage. Keep HOLDING the button to continue the count to the 10 second 'Firmware' stage. When the 'POWER' LED blinks 7 times at a faster rate (about 2x) than the 3-blink/(configuration) stage, it has then reached the 'Firmware' version factory default stage and will reset the firmware when the button is released. This will not affect the Configuration data.

Added additional video formats and resolutions to the '^SLT-1,videomode=<format>,<resolution>' send command. The following are now allowed:

send_command 10001:1:0,"'^SLT-1,videomode=hdmi,640x480p@30'"
send_command 10001:1:0,"'^SLT-1,videomode=hdmi,800x600p@30'"
send_command 10001:1:0,"'^SLT-1,videomode=hdmi,1024x768p@30'"
send_command 10001:1:0,"'^SLT-1,videomode=hdmi,1280x720p@30'"

send_command 10001:1:0,"'^SLT-1,videomode=dvi,640x480p@30'"
send_command 10001:1:0,"'^SLT-1,videomode=dvi,800x600p@30'"
send_command 10001:1:0,"'^SLT-1,videomode=dvi,1024x768p@30'"
send_command 10001:1:0,"'^SLT-1,videomode=dvi,1280x720p@30'"

send_command 10001:1:0,"'^SLT-1,videomode=vga,640x480p@30'"
send_command 10001:1:0,"'^SLT-1,videomode=svga,800x600p@30'"
send_command 10001:1:0,"'^SLT-1,videomode=xga,1024x768p@30'"
send_command 10001:1:0,"'^SLT-1,videomode=wxga,1280x768p@30'"

send_command 10001:1:0,"'^SLT-1,videomode=component,720x480i@30'"
send_command 10001:1:0,"'^SLT-1,videomode=component,720x480p@30'"
send_command 10001:1:0,"'^SLT-1,videomode=component,720x576i@30'"
send_command 10001:1:0,"'^SLT-1,videomode=component,720x576p@25'"

send_command 10001:1:0,"'^SLT-1,videomode=svideo,ntsc'"
send_command 10001:1:0,"'^SLT-1,videomode=svideo,pal-bghid'"
send_command 10001:1:0,"'^SLT-1,videomode=svideo,pal-m'"

send_command 10001:1:0,"'^SLT-1,videomode=composite,ntsc'"
send_command 10001:1:0,"'^SLT-1,videomode=composite,pal-bghid'"
send_command 10001:1:0,"'^SLT-1,videomode=composite,pal-m'"

Known Issues

• Video input format reports as PAL-BGHID on the ModeroX if no source is connected and the configuration is set for COMPOSITE,NTSC. It corrects itself after the COMPOSITE cable is connected.
• Due to the wide variety of video graphics cards on the market it is possible that some video chipsets may not work properly when connected directly to the MP(L), especially when using the VGA, SVGA, XGA, and WXGA formats. The chipsets that have been tested (though others may also work) are:
• Intel(R) HD Graphics 3000
• AMD Radeon HD 6750M
• NVIDIA GeForce 8200M G